“No hard disks to display” error occurs when some users of Windows 7, Windows 8.1, or Windows 10 try to run the tool

You are watching: < font style = "vertical-align: inherit;"> disk part there are no fixed disks to display

the “No hard disks to display” An error occurs when some Windows 7, Windows 8.1, or Windows 10 users try to run the DiskPart utility. Most affected users report that the computer cannot boot from a connected hard disk (but can boot from a Windows installation medium).

No hard disks to display errors when running DiskPart

What is causing the error show “?

  • The hard disk is incorrectly connected – It turns out that one of the most common causes of this particular error is a hard disk that is not connected properly. In most cases, this happens if the SATA or ATI data cable is not pushed all the way in or does not work. In this case, you can fix the problem by opening the cover of your laptop or PC and restarting the computer without a hard disk before re-establishing the connection.
  • VMware driver is missing – If you encounter this issue after a NAT lock when using a VMware virtual machine, it is probably the immediate result of a kernel panic. To restore the Windows installation in this case, you need to rely on recovery mode to get everything working again. To do this, you must run a series of CMDs at an elevated command prompt.
  • Damaged BCD data – Several affected users have confirmed that this problem may also occur due to of any form of system file corruption in boot configuration data. In this case, you should be able to fix the problem by opening an elevated command prompt and rebuilding the corrupt BCD files with a series of commands.
  • Initialization Error – An initialization error can also be the root cause until this particular error message is displayed. If this scenario is applicable, the best possible solution for end users is to use the Automatic Repair tool. But to implement this solution, you must have a compatible Windows installation medium.

How do I fix No Fixed Disks to show errors?

Now that we understand them most likely the causes of this error, let’s proceed to the steps that you should take to troubleshoot and resolve the issue.

1. Hard Disk Reconnection

As several concerned users have reported “No hard disks to display” The error may very well be due to a hardware consequence caused by a pin that is not connected properly.

If you have recently made any hardware changes (for example, moved your installation to a new box or moved the hard disk from one machine to another), the first step is to make sure that the hard drive is properly connected.

Here are some step-by-step instructions to make sure the hard drive is properly connected:

  1. Turn off your machine completely and make sure the power is off completely by removing the cord from its socket.
  2. Please equip yourself with an electrical wristband (if you have one) and open the case of your computer / laptop.
  3. Remove the SATA / ATA data and power cables from the hard disk drive, and then turn on the computer long enough for it to recognize that the hard disk is no longer connected.
    Disconnect the cables from the hard disk
  4. You will receive an error message stating that there is no storage device connected to this computer. As soon as you see it, if the computer shuts down again and reconnects the two cables, make sure both are securely connected (pressed all the way).
  5. Restart the computer and see if the problem is resolved. .

If you are still experiencing the same “No hard disks to view” error, go down to the next potential solution below.

2. VMware driver installation missing (if applicable)

If you encounter this issue related to a NAS crash while using a VMware virtual machine, it may be due to some kind of kernel panic. Usually in situations like this, the problem will break the Windows installation, making it completely reboot.

We were able to find several events with users in a similar situation who tried to fix the problem by use Windows Recovery Mode to get everything working again. Unfortunately, during the partition section, DiskPart “No hard disks to display” was displayed errors that paralyzed the repair procedure.

If this scenario applies to your current situation, it is highly likely to occur due to by using VMware PVSCSI for your virtual disks. Fortunately, this can be solved by a series of commands run from an elevated CMD prompt.

Here’s what to do:

  1. On your Vmware workstation, right-click on your virtual machine and click Install Vmware Tools . Then select mount in the next menu and wait until the procedure is complete.
    Install vmware tool
  2. With the virtual machine installed, you should return to the Windows recovery menu. To do this, press Windows key + R to open the Run dialog box. Once inside, type ‘cmd’ and press Ctrl + Shift + Enter to open an elevated CMD prompt. when you see UAC (User Account Control) click Yes grant administrative privileges.
    Run Command Prompt
  3. Once inside the elevated CMD prompt, type the following command and press Enter:

     drvload "X: Program FilesVMwareVMware ToolsDriverspvscsiWin8amd64pvscsi.inf" 

    < p class = "gt-block"> Note: X is just a placeholder. Replace it with the correct letter where VMware is installed.

  4. Once the command has been successfully processed, run the following command and press Enter to see if you can use the Diskpart tool without finding ” No hard disks to display “ errors:
     X: windowssystem32 & gt; disk part
    

    Note: Remember that X is just a placeholder. Replace it with the drive letter for your operating system.

  5. If the process was successful and you no longer encounter the same error, reinstall the virtual machine and you are done.

< h3> 3. BCD Data Correction

It turns out that this problem can also occur because your system is struggling with some logical errors or even system corruption within Startup Configuration Data . If this scenario applies, you should be able to resolve the issue by rebuilding the BCD files with a series of CMD commands.

Several affected users have confirmed that this operation allowed them to access the DiskPart screen and complete the operation without encountering ” No hard disks to display “ errors.

Here’s a quick guide to what you need to do:

  1. Insert a compatible installation medium into your computer and restart your computer to boot from it.
    Note: If you do not have one, you can create a compatible installation medium from a known computer .
  2. To boot from the installation medium, press any key when you see the black screen and wait for the first installer to load. rc = “https://static.codepre.com/uploads/1648057797.jpg” width = “521” /> Press any key to boot from the installation media
  3. After booting from the installation media, click you on Repair your computer (lower left corner) and wait for the repair tool to load.
    Click Repair your computer on the Windows screen

    Note: In Windows 10, you can enter the repair menu even without the installation medium: by forcing 3 consecutive unexpected machine interruptions (by shutting down the computer in the middle of the startup sequence).

  4. Once you have entered the first repair menu, click the Troubleshooting menu from the list of available options. Then click Command Prompt from the list of sub-options.
    Click Command Prompt
  5. Once inside the newly opened command prompt window, type the following command in order and press enter < after each to rebuild boot configuration data:
     Bootrec / scanos Bootrec / fixMBR Bootrec / fixBoot Bootrec / rebuildBCD 
  6. After each command has been successfully processed, close the CMD prompt and restart the computer to see if the problem persists at the next system boot.

Yes, it’s the same “No hard disks to show” error continues to occur, please go down to the next potential solution below.

4. Using Windows Startup Repair

If none of the previous instructions allowed you to resolve the issue “No hard disks to display” and run the DiskPart utility normally, it’s probably some kind of initialization error caused by one or more kernel files.

If this scenario applies, you should be able to quickly fix the issue with the most powerful the tool available to end users: the Automatic Repair tool. Some users who also encountered this issue reported that the issue was completely resolved and that they could start normally after completing the instructions below.

IMPORTANT: > The following procedure should be compatible with all Windows installation media. But you must have a compatible installation medium to be able to replicate the instructions below. If you do not have a compatible installation medium, create one for Windows 10.

If you already have one compatible installation media or used the previous wizard to create one, follow the instructions below to use the initial repair tool to fix the problem automatically. Here’s what you need to do:

  1. Turn on your computer (restart it if it’s already on) and make sure the Windows installation media is inserted in your DVD drive or USB port.
    Note: Note that if you are using a USB memory stick as your installation medium, you will probably need to make sure your computer is set to boot from it first.
  2. When you see your computer getting ready to enter the boot sequence, wait patiently until you see the black screen that says “Press any key to boot from CD or DVD”. When you see it, press any button to start from this particular installation medium image-418525 “height =” 125 “src =” https://static.codepre.com/uploads/1648057797.jpg “width =” 521 “/> Press any key to start from the installation medium
  3. When you get to the first installation screen, turn your attention to the lower left corner of the screen and click on the repair your computer hyperlink located in the lower side of the screen.
    Click Repair Your computer on the Windows screen
  4. After several seconds of charging, you should see the troubleshooting menu. Once you get there, you have the opportunity to choose from several options. Be sure to click the troubleshoot function.
    Click Troubleshoot
  5. From the Troubleshooting menu, click Advanced Options from the list of available recovery options.
    Automatic repair in advanced options
  6. If you have a dual boot installation, you will be asked which operating system you want to repair. Select it and then wait patiently until the process is complete.
    car repair screen
  7. When the task is complete, remove the installation media and restart the computer to see if the problem is resolved.


See more information related to the topic disk part there are no fixed disks to display

How To Fix HP No Hard Drive Found, Hard Drive Not Detected, Hard Drive Not Installed, No HDD

alt

  • Author: PC Monkey
  • Post date: 2020-03-24
  • Ratings: 4 ⭐ ( 1064 Ratings )
  • Match search results: This video will show you a few fixes for the errors; No HDD Found, HDD Not Installed, HDD Not Detected, No Boot Device, No Bootable Device, Boot Device Not Found, Exiting PXE ROM, etc. Often times, this error has nothing to do with a bad Hard Drive. This video takes you through the base system, operating system, and hardware fixes. If the diagnostic shows all components to be healthy and none of the other steps solved your issue, then try to Factory Reset your HP as seen here; https://youtu.be/CWUaIJ4RhWU. If that fails, then you would have to reinstall the Operating System as seen here; https://youtu.be/p_N_xV7j_Xo. You can create your own Install Media for free as seen here; https://youtu.be/g_UhiHScaSI. If you cannot create your own, then you would have to purchase it. Let me know if you would like help finding the correct one.

    To Donate to PC Monkey so I can keep making relevant videos on newer computers, use https://www.gofundme.com/f/pc-monkey or CashApp at $PCHelper.

    FAQ’s;
    Q: What keys are you pressing?
    A: F2 for the Diagnostic Options and F10 for the BIOS options. At 4:08, I’m tapping on F10

    Q: My test does not have a Hard Drive option.
    A: Storage is the same as Hard Drive.

    Q: My Short or Long DST Failed. What does that mean?
    A: If your HDD failed the test, that means your Hard Drive is bad and needs to be replaced. You can see that here; https://youtu.be/tNp5Kbo9uHg. Then you would need to install Windows 10 onto the new drive as seen here; https://youtu.be/p_N_xV7j_Xo. You can create your own Install Media free as seen here; https://youtu.be/g_UhiHScaSI

    Q: The test said ‘Not Installed’ or ‘Not Available’. What does that mean?
    A: That means your Hard Drive is either bad or loose. I would first try ‘reseating’ the Hard Drive. That is where you unplug it and then plug it back in, making sure its properly plugged in and secure. Try the scan again. If it still says that its not installed, then its most likely bad and needs to be replaced. You can see how to do that here; https://youtu.be/tNp5Kbo9uHg. You would also then need to install an operating system onto the new one as shown here; https://youtu.be/p_N_xV7j_Xo. You can create your own Install Media for free as seen here; https://youtu.be/g_UhiHScaSI.

    Q: My diagnostic test says ‘Unavailable’ or I cant run it. What do I do?
    A: First reseat the HDD. See if that helps. If you cant run the test, then we don’t know for sure if the HDD is bad or not. You can proceed a couple different ways. You can assume its good and that the Operating System is the cause of your error. Or you can assume its bad and replace it before installing an Operating System to the new one. You can see how to install Windows 10 to an HP here; https://youtu.be/p_N_xV7j_Xo. You can create your own Install Media for free as seen here; https://youtu.be/g_UhiHScaSI.

    Related Video Links;
    Computer Wont Turn On Fix
    https://www.youtube.com/watch?v=_MOe71kBPOY&feature=youtu.be
    HP Boot Loop / Restarting Fix
    https://www.youtube.com/watch?v=_qF-oqPrn7M&feature=youtu.be
    Computer Turns On But Screen Stays Black
    https://www.youtube.com/watch?v=u-REPLdpZ70
    How To Replace Hard Drive in a Laptop
    https://www.youtube.com/watch?v=PLiCtwOBuxk

[2 Tricks] Disk 1 No Media Diskpart or Disk 0 No Media Diskpart

  • Author: www.icare-recovery.com
  • Ratings: 5 ⭐ ( 3316 Ratings )
  • Match search results: External disk 1 no media diskpart or disk 0 no media diskpart fixing on this page to guide you solove the disk no media with diskpart when it reported there is no media in the device when you use command prompt diskpart to delete clean format the disk however it did not show up in disk management or diskpart.

There are no partition disks to install windows 7

  • Author: answers.microsoft.com
  • Ratings: 5 ⭐ ( 5406 Ratings )
  • Match search results: I cant reinstall windows 7 because when I try to load the windows and format the previous one (win 10 insider preview) there is no partition to select …..

No fixed disks : SCCM

  • Author: www.reddit.com
  • Ratings: 3 ⭐ ( 1454 Ratings )
  • Match search results: I’m having an issue imaging an HP 800 G2, all of a sudden I’ve been getting reports from our desktop techs of the task sequence failing early on in …

DiskPart Error ‘No fixed disks to show’

  • Author: appuals.com
  • Ratings: 4 ⭐ ( 7037 Ratings )
  • Match search results: The ‘There Are No Fixed Disks to Show’ error is encountered when some Windows 7, Windows 8.1 or Windows 10 users are attempting to run the DiskPart

Windows in recovery mode: No fixed disks to show

  • Author: patrik.kernstock.net
  • Ratings: 5 ⭐ ( 5575 Ratings )
  • Match search results:

Solved: There Are No Fixed Disks to Show

  • Author: www.diskpart.com
  • Ratings: 5 ⭐ ( 7016 Ratings )
  • Match search results: Get an error says “No drives were found” during Windows installation. When you turn to Diskpart, it shows “There are no fixed disks to show”. How to solve it?

See more articles in this category: Computer tips